**銷售日本YUKEN電磁換向閥
上海乾拓貿易有限公司
企業QQ：
電話；021-69001039
手機；17321017802（微信）
郵箱；17321017802@163.com
地址：上海市嘉定區江橋嘉涌路99弄6號樓713室
此外，使用濕式電樞螺線管，閥門可確保使用壽命長。
These DSG-005 series solenoid operated directional valves are the pro- ducts newly developed as a "Mini-series".
 Compared with DSG-01 series, t he valves are much more compactly manufactured but enjoy a maximum operating pressure of 25 MPa (3630 PSI)
 and a maximum flow rate of 10 L/min (2.6 U.S.GPM),
油箱端口不要將油箱端口連接到其中具有浪涌壓力的任何管道。
Always be sure to use hydraulic fluids within the stipulated conditions shown below:
子板可用。從上表中**子板型號。
Mounting Posture For any model, there are no restrictions regarding the mounting posture.
請注意浪涌電壓。安裝姿勢對于任何型號，安裝姿勢沒有任何限制。
 Please maintain the degree of contamination within NAS 1638-Grade 1 1.  Use 20 μm or finer line filter. Control of Contamination
Solenoids Instructions As the solenoids have no surge absorbers, please pay cautious attention to a surge voltage.
安裝螺栓包括表中的四個內六角頭螺釘。
與DSG-01系列相比，閥門制造更加緊湊，
但工作壓力為25 MPa（3630 PSI），
流量為10 L / min（2.6 USGPM），
同時進一步提升了空間 節省要求。
螺線管通電當給一個螺線管通電時，請務必先預先關閉另一個螺線管。
 Tank Port Do not connect the tank port to any pipe line having a surge pressure in it.
 Be sure to keep the end of the tank line p ipe below the oil level.  As the solenoids are of wet type structure,
it is necessary to make piping in such condition that the inside of the valve is always filled with the fluid.
2粘度：20-200 mm / s（100-930 SSU），
溫度：-15至+ 60°C（5至140°F）。**的粘度和油溫
必須注意保持對液壓油污染的控制，
否則可能會導致液壓油的損壞，并縮短閥門的使用壽命。
請保持NAS 1638-Grade 1中的污染程度
Sub-plates are available. Specify the sub-plate model number from the table above. 
When sub-plates are not used, the mounting surface should have a good machined finish.
1.使用20μm或更細的線路濾波器。控制污染
螺線管說明由于螺線管沒有浪涌吸收器，
 while contributing further to a space saving requirement. 
Moreover, using wet armature solenoids, the valves ensure the long life.
電磁式方向閥DSG-005
流體類型液壓油可以使用表中列出的任何類型的液壓油。
確保將油罐管線的末端保持在油位以下。
由于螺線管是濕式結構，因此必須在閥內部總是充滿流體的狀態下進行配管。
Solenoid Operated Directional Valves DSG-005
Fluid Types Hydraulic Fluids Any type of hydraulic fluid listed in the table below can be used.
Mounting Bolts Four socket head cap screws in the table below are included.
這些DSG-005系列電磁換向閥是新開發的“迷你系列”產品。
2  Viscosity:  20-200 mm /s (100-930 SSU), Temperature:  -15 to+60°C (5 to 140°F). Recommended Viscosity and Oil Temperatures
Solenoid Energisation When energising one solenoid, be sure to de-energise another solenoid beforehand.
當不使用子板時，安裝表面應具有良*的加工精加工。
始終確保在下列規定條件下使用液壓油：
Due caution must be paid to maintaining control over contamination of the hydraulic fluids
 which may otherwise lead t o breakdowns and shorten the life of the valve.

**銷售日本YUKEN電磁換向閥